Brookfield DV3T Rheometer Bedienungsanleitung PDF herunterladen (Seite 109)

Brookeld Engineering Labs., Inc. Page 109 Manual No. M13-2100

WhenaULorDINULAdapterisused,thewaterbathisstabilizedatthepropertemperature:

1) PuttheproperamountofviscositystandarduidintotheULTube(refertotheUL

Adapterinstructionmanual).

2) Attachthespindle(withextensionlinkandcouplingnut)ontotheDV3T.

3) Attachthetubetothemountingchannel.

4) Lowerthetubeintothewaterbathreservoir,orifusingtheULA-40Ywaterjacket,

connecttheinlet/outletstothebathexternalcirculatingpump.

5) Allow30minutesfortheviscositystandard,samplechamberandspindletoreachtest

temperature.

6) MeasuretheviscosityandrecordtheRheometerreading.

Note: The spindle must rotate

at least ve (5) times before readings are taken.

Calibration Procedure using a Helipath Stand and T-Bar Spindles

 WhenaHelipathStandandT-Barspindlesareused:

1) RemovetheT-barspindleandselectastandardLV(#1-3)orRV,HA,HB(#1-6)spindle.

FollowtheproceduresforLV(#1-3)andRV,HA,HB(#1-6)Brookeldspindlesoutlined

above.

2) T-Bar spindles should not be used for verifying calibration of the DV3T Rheometer.

Calibration Procedure for Spiral Adapter

Brookeldrecommendsatwostepcheck.First,verifythecalibrationoftherheometerusingthe

standardrheometerspindles(LV#1-3,RV#2-6,HA#2-6andHB#2-6orcone/platespindles)

asdetailedinthisappendix.Second,verifythecalibrationoftherheometerusingtheSpiral

Adapter.Theuseofanaccessorydevicemayincreasetheaccuracyofmeasurementassociated

withtheDV3T.

1) Placetheviscositystandarduid(inthepropercontainer)intothewaterbath(referto

theSpiralAdapterinstructionmanual).

2) Attachthespindletotherheometer.Attachchamber(SA-1Y)andclamptotherheometer.

3) LowertheDV3Tintomeasurementposition.Operatetherheometerat50or60RPM

untilthechamberisfullyooded.

4) The viscosity standard uid, together with the spindle, should be immersed in the

bathforaminimumof1hour,stirringtheuidperiodically(operateat50or60RPM

periodically),priortotakingmeasurements.

5) After1hour, check the temperatureoftheviscosity standard uidwithanaccurate

thermometer.

6) Iftheuidisattesttemperature(

+/-0.1°Cofthespeciedtemperature,normally25°C),

measuretheviscosityandrecordtherheometerreading.

Note: The spindle must rotate

at least ve (5) times for one minute, whichever is greater before readings are taken.

7) TheviscosityreadingshouldequalthecPvalueontheviscosityuidstandardtowithin

thecombinedaccuraciesoftherheometerandthestandard(asdiscussedinthesection

entitled,InterpretationofCalibrationTestResults).However,instrumentaccuracyis

±2%ofthemaximumviscosityrangeandnotthestandard1%.

1 2 ... 104 105 106 107 108 109 110 111 112 113 114 ... 124 125

Kommentare zu diesen Handbüchern

Keine Kommentare

Brookfield DV3T Rheometer Bedienungsanleitung Seite 109

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Messgeräte Brookfield DV3T Rheometer